D-GA44Q FUEL DISPENSER

D-GA44Q FUEL DISPENSER

FlowMeter Type: Optional

Accuracy: ±0.2%

Pressure Loss (kg/cm): Under 0.25

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle: Auto Shut-off Nozzle

Environmental Condition: -40~~+55degree

Control Type: Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price :0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display: Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose: 4.5m

Weight : 335kg.

Dimension(L×W×H): 1270 x 620 x 2420(mm)

Dimension(L×W×H)Of Qty of Container: 40ft: 45 20ft: 22

result during approval progress. The other is to make adjustment as temperature fluctuate 20 degree. St fuel dispenser opwatch, minimum value 0.1 second, is used for measuring how long a certain volume medium discharge out of fuel dispenser so as to calculate its flow rate. Gradienter, precision being 0.05mm/m, measures the degree of level. Article III Indicating appraisal method and data processing Appraisal of fuel dispenser actually is an indicating access. Presently, cubage compare method is mostly used defining basic tolerance between the volumes flow over flow meter and in metal standard measurer. Diagram 6-2 is illustrated the fuel dispenser’s appraisal flow. 1: Check valve 2: Pump 3: Vapor separator 4: Flow meter 5: Indicating device 6: Hose 7: Nozzle 8: Standard measurer 9: Measurer 10: Switch & zeroing 11: Container 12: Motor 13: Tank 14: Filter net Diagram 6-2: Appraisal of fuel dispenser using metal standard measurer Preparation before appraisal Place metal standard measurer on the hard ground and adju fuel dispenser st with gradienter. It also put on vehicle or other bracket, as long as not waving or vibration during appraisal progress. Metal standard measurer should be earthing- connected. It is suggested to connect the measurer to ground terminal of fuel dispenser, making them being same potential. Running-in and wet measurer. Putting indicator device at zero, open nozzle and observe oil indicator. Oil is transparent as there is no foam in it. If have foam or bubble oil would be feculent and opaque. If foam exists in oil for a long time, fuel dispenser would have trouble. Appraise again af fuel dispenser ter solving failure. Close nozzle as measurer full of oil. Empty measurer in accordance with relative method and time, and shut off bottom valve, putting measurer in preparation state. Appraisal procedure of indicating valve Set unit price; Adjust flow to the maximum Qmax; Wet measurer and place it according to regulation; Tune indicator finger to zero position; Infuse measurer as preset volume, measure outlet t

s　　 additional weights used and is only 0.005 mg.　〠fuel dispenser €Poids et Mesures) CIPM key comparisons　　have been conducted for several years in　　 The CCM key comparisons CCM.M-K1 (mass:　　various fields. In the following important　　 1 kg) CCM.M-K2 (mass: 100 mg to 10 kg) and　　activities as well as significant research and　　 CCM.M-K3 (mass: 50 kg) were carried out　　development work of the Division will be　　 with 15 state institutes the Mass Laboratory　　presented.　　 of the PTB acting as pilot laboratory. With　　 some exceptions the results of the various　　1.1 Mass　　 participants are in very good agreement. All　 fuel dispenser 　The Mass Department is composed of the deviations of the PTB values from the refer-　　working groups Realization of Mass Weighing ence values (e. g. 1 碌g for 1 kg) clearly lie　　Instruments Dynamic Weighing IT Weighing within the calculated uncertainties.　　Technology and Gravimetry.　　 In the field of type approval for weighing　　In the area of precision mass determination instruments the bilateral cooperation agree-　　substantial progress could be achieved in the ment concluded in 2001 bet fuel dispenser ween the PTB and　　reduction of the uncertainty component due the Chinese certification authority AQSIQ　　to air buoyancy: By the use of special buoy- could for the first time be successfully imple-　　ancy artefacts it was possible within the mented. So a German manufacturer of weigh-　　framework of the project Redetermination of ing instru

killed in one such clash. A shadowy group calling itself the Movement for the Emancipation of the Nig fuel dispenser er Delta, which demands that more of the oil revenues go to the local people, is responsible for most of the mayhem. So effective has its campaign been that it has managed to shut down about 20% of the country s oil production. But as well as the threat to the oil industry, which provides some 80% of the government s revenue, there is increasing nervousness about the state of democracy ahead of presidential and state elections due to be held in April next year. The elections that Mr Obasanjo, a former general, won in 1999 had seemed to end a depressing cycle of decades of military coups and dictatorships. Nigerians were hoping next year to see the first-ever peaceful handover from one elected president at the end of his constitutional term to another. Instead, they have witnessed an ominous rise in political recrimination and violence. Already, three gubernatorial aspirants have been assassinated. Po fuel dispenser litics has become blighted by a bitter clash between Mr Obasanjo and his vice-president, Atiku Abubakar, who are now trading accusations of corruption against each other. Relations between the two deteriorated after Mr Obasanjo s bid, earlier this year, to alter the constitution in order to allow him to run for a third term of office. Mr Abubakar resisted this, saying that it proved the president was bent on exercising “absolute power� Despite bribes of up to 50m naira ($400,000) to senators, and what an Abubakar ally, Usman Bugaje, the chairman of the House of Representative fuel dispenser s committee on foreign affairs, alleges were texted death threats that the “government was obviously involved in� the Senate voted against the bid. The affair seemed to mark the beginning of a vendetta against Mr Obasanjo s political opponents and a return to the bad old days of Nigerian politics, with summary arrests of Abubakar supporters and break- ins at his campaign headquarters. The intention is cl