K-G22 FUEL DISPENSER

K-G22 FUEL DISPENSER

Pump : Type Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.): 55±5

Suction Distance (m): 6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy : ±0.2%

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp): 1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition :-40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :ype LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight :280kg

Dimension(L×W×H): 1180*650*2020(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 29

on and n fuel dispenser oise of pump, finding whether leakage between axis end and pump cover, checking the excessive jump and swing of V wheel that is called belt wheel past, but now defined as V wheel in GBT/10412�?002 General V Wheel. Don’t use water and oil with water to debug or cleanse tank in case of the pump and components of fuel dispenser is rust. Meanwhile preventing freeze water affect the normal operation because of low temperature. Regularly inspect and cleanse strainer, especial after installation a pipeline. With the working time get long the waste in pipeline or tank decrease, the period of checking and cleanse should considerably lengthen. But don’t exceed one month. The strength of V wheel should be appropriate because low strength result in no oil discharge out or inefficiency. High strength, in another case, would increase the axis loan of motor and pump, fasting bearing abrasion of motor, pump and oil seal. Don’t adjust overflow valve to tight in case of increasing pump pressure so as to flux passing fuel dispenser overflow valve, and well as noise, vibration and abrasion. Judgment for common failures Firstly, some failure analysis and correct judgment is necessary before maintenance. The principle of first analysis then disassemble, easy first is the basis to judge trouble. The common failure phenomenon of vane pump is that no delivery, inefficient flux, leakage, noise and abnormal vibration. They will be introduced one by one. No delivery or inefficient flux Apart from pump failure other component and pipeline trouble may also result in this phenomenon. Here only introduce pump failure and inspection method. Exterior inspection: to check motor that maybe don’t work, or rotate in opposite direction, or lose V wheel. Reversal result from wrongly connecting two phase wire in motor or power supply. Adjusting strength of V wheel or changing a new one deal with wheel slip. However, the reason that motor don’t work are several, either electric or mechanical failure. Disconnecting V wheel at first, fuel dispenser

alarm b fuel dispenser ut lower than that of　　 the Hi-Level alarm.　　LoLo-Level Alarm The highest product level which should never be exceeded for safety　　 purposes. When the LoLo-Level alarm is active there is an emergency　　 situation.　　Hi-Water Alarm The highest water level that is allowable for operational purposes. When　　 the water level exceeds the Hi-Water value there is an increasing risk of　　 the pumps sucking water into the line.　　January 2005 IFSF - STANDARD FORECOURT PROTOCOL Version 1.25　　 TANK LEVEL GAUGE APPLICATION　　 Page: 51　　5 Implementation Guidelines Recommendations　　This section gives guidelines recommendation for implementations of the IFSF Tank　　Application Protocol.　　5.1 Handling after a Device Master ResetCold S fuel dispenser tart or Initial Start-up　　After a master reset cold start initial start-up or discovery that the device s configuration is　　corrupted the Tank Level Gauge should:　　 Initialise the Communication Specification s Heartbeat_Interval to 10 seconds.　　 Start generating Heartbeat messages with a Device_Status indicating that configuration is　　 required.　　 Reset the Communication Specification s Recipient Address Table.　　 Where a default value exists for a Data_Id the dispenser should set up the Data_Id s value　　 accordingly.　　5.2 Handling after a Reset or Power Off　　After a master reset of the Tank Level Gauge the device should:　　 Check that device configuration is valid. If the configuration is corrupt please treat the　　 condition as described for master resetcold start (see above).　　 Do not clear the Communication Specification s Recipient Address Table.　　 Do not reset Data_Id s t fuel dispenser

message fuel dispenser through the media by issuing a one-way press release, but that s as flawed right now as a 15 or 30-second TV ad,�? says Pam Talbot, Edelman s chief in America. The fragmentation of media has seen an explosion in the number of ways people seek news and entertainment, with many turning to websites, cable TV, satellite radio and podcasts. Yet a consequence of the proliferation of media is that original content becomes even more sought after. Hence crisply written or well-produced PR material can more easily get an airing. Media commentators have noted how PR material is now being published by some local newspapers virtually unedited and unchecked. Some branches of journalism have come to depend on a drip- feed of information and products from the PR industry. Journalists focusing on electronics, fashion, travel, beauty and food have a huge appetite for free samples. Gossip about celebrities is also largely mediated by the PR industry. Never shy about accentuating the positive, the PR industry mig fuel dispenser ht be expected to be trumpeting its rise. And there is indeed some triumphalism (and spin) around. Al and Laura Ries, a father and daughter team of marketing consultants, have written a book entitled “The Fall of Advertising & the Rise of PR�? “PR has credibility,�?they assert “Advertising does not.�?Their advice is that a marketing campaign should start with publicity and shift to advertising only after the PR objectives have been achieved. Some PR firms see an opportunity to move up their clients hierarchy—becoming not just service providers, but also purveyors of strategic advice to senior management. But even within the industry, there are sceptics. Dorothy Crenshaw, president of Stanton Crenshaw, an independent PR firm based in New York, says that many of her colleagues are suffering from “consultant envy”�? but that PR remains a very inexact science. There are also limits to the miracles it can be expected to achieve. She claims to have turned down a $1m commissi fuel dispenser